wiring a ceiling fan with light when all wires are black

WIRING A CEILING FAN WITH LIGHT WHEN ALL WIRES ARE BLACK MANUAL
WIRING A CEILING FAN WITH LIGHT WHEN ALL WIRES ARE BLACK PROFESSIONAL

Also, make sure to strip the ends of your wires to expose the copper end. Wu Pin LJY-280A 4-hole fan switch: Black wire in terminal 3 and terminal number L-1-2-3 is in. Shine Top LS-102 fan switch: Black wire in terminal 3 and terminal number L-1-2-3 is in counterclockwise order.

WIRING A CEILING FAN WITH LIGHT WHEN ALL WIRES ARE BLACK PROFESSIONAL

If needed, consult a professional electrician to ensure that your breaker box and electrical switches are to code. Defond 4-hole fan switch: Black wire in terminal 3 and terminal number L-1-2-3 is in counterclockwise order.

Red wire is sometimes included and acts as a conductor to carry power to the light kit.īefore you begin, make sure all electrical circuit breakers related to the wiring are turned off. Carefully lift the glass up to the fan and turn clockwise until the glass is snug. Plug the light into the fan, then screw in the mounting ring and the light with three keyhole screws. My fan has a mounting ring as well as an LED light.

WIRING A CEILING FAN WITH LIGHT WHEN ALL WIRES ARE BLACK MANUAL

If you had a red wire coming from your ceiling, it is hooked up to your wall switch.īlue wire is for the light, if light is included with the fan. Follow your instruction manual for attaching the lighting kit. If you have a blue and black wire coming from your household circuit, you should have two switches on your wall. The white wire is neutral and completes the electrical circuit.Ĭopper or green wire is the ground wire and keeps your fan from experience power surges. The black wire is the hot wire that leads to the switch. Wiring a ceiling fan with four wires is the most common, however, an additional color wire may be incldued. Always place wire caps over unused wires. It's important to understand what each wire does and how it connects with the others. That is what your fan needs.Ceiling fan wire colors may be slightly different than your household circuit wires. Three wires remain: blue, red and white which is actual neutral. Up in the fan box, black gets nutted to black (which is the white wire remarked black, and NOT the black wire remarked blue). The power for the fan motor will typically be black, while most modern-day fans also have a separate blue wire that supplies power to the lights. Ok, now counting the tape color, black = always hot, blue = switch 1, red = switch 2 and white is neutral. Also mark the red pigtail with blue tape.

get blue tape, and on the /3 cable, mark both ends of the black wire with blue tape.

The black wire exits the cable in the switch box, and hits a wirenut to connect to a red (!!!) pigtail that goes to a switch.

The red wire exits the cable in the switch box, and hits a wirenut to connect to a red pigtail that goes to a switch.

They are both short pigtails, also mark the red wire with black tape near each end, which will reduce confusion in that box.

You see in the switch box where the white wire joins a black and red wire in a wirenut.

Use a stepladder to reach the wires in your ceiling and carefully cut away the plastic coating about 2 inches (5.1 cm) from the end of the wires with a wire cutter. Remove the plastic caps that are on the ends of your wires. This is the only mandatory marking the rest a done for sanity's sake. To connect your wires, the copper ends must be exposed. Use of the white wire for always-hot is mandatory in this case, but also mandatory is the marking I just described.

Mark both ends of the white wire with black tape, to designate that it is for 'always-hot'.

Your fan should have a green, white, and black wire coming out of the top of it. So, there you have it These 9 simple steps have probably proven to you that replacing a ceiling fan with a light fixture is work you don’t really need an electrician for. Examine the wires coming out of your fan. Remember, the black wire goes with black wire (or red), white on white, and the ground wires go together. It is the same cable both in the fan box and the switch box. You know, with wires, you will have to be extra meticulous. There is one /3 cable (black white red) since ground is not counted as a conductor.

This deal is sorely in need of some colored electrical tape. Line up the matching wires so they are parallel, then screw on a wire nut to each set: White to white black to black.

Wiring a ceiling fan with light when all wires are black